social linkedin box blue 32
social facebook box blue 32
social twitter box blue 32
social facebook box blue 32

iit-advr-logo-v3

Research ■ Hydraulic Control

Hydraulic Control


Most of the high-performance robots built to date employ hydraulic actuation. Examples such as BigDog, LS3, HyQ, and Petman enhance the potential of this actuation technology. Hydraulics has many properties that make it an ideal choice for highly dynamic articulated robot applications:

hyq roundedCorners
    • Higher power-to-weight ratio;
    • The centralized power source (pump + tank) can provide power for several actuators. This permits to distribute better the actuation weight, keeping the robot base heavier and the links lighter;
    • The hydraulic transmission, characterized by the fluid, is stiffer than electric drives transmissions (e.g. gear box), resulting in the possibility to have higher closed loop gains, greater accuracy, and better frequency response;
    •  Hydraulic actuators are mechanically very simple and allow for robust design against impacts and overload. This is very important in dynamic applications, where high peak forces on the robot structure cannot be avoided and are even part of the requirements
    •  Hydraulic actuators (e.g. valves) guarantee high enough actuator bandwidth to achieve near perfect torque control in the spectrum of interest for dynamic locomotion of medium to large scale robots. This provides legged robots, such as HyQ, the compliance needed for legged locomotion by using a naturally very stiff actuation system;
    • The hydraulic fluid serves also as coolant of the actuators.
                                                                                                                                                                                                        Figure 1: Hydraulically actuated robot - HyQ      


The HyQ leg prototype consists of two links and it has three actuated degrees of freedom (DOF): two in the hip (abduction/adduction and flexion/extension) and one in the knee (flexion/extension). Both flexion/extension DOF are actuated by small-sized hydraulic components: an asymmetric hydraulic cylinder (Hoerbiger LB6 1610 0080) driven by high-performance electro-hydraulic servovalves (Moog E024). For more details about the HyQ design, check its website!

      HoerbigerCylinder    MoogE024 inHand     CylinderAndMoog

Figure 2: HyQ cylinder (left), valve (center), and valve assembled with a custom made manifold on  the cylinder (right)



Hydraulic Control Architecture

Being able to apply precise joint torques to a robot has many advantages. Torque control allows various forms of impedance control, control of contact forces, virtual model control, as well as model-based controls, such as rigid body dynamics based control (inverse dynamics, gravity compensation), and operational space control.

HyQ's legs employ a control scheme composed of two different closed-loop controls: an outer position loop and an inner torque loop, as described in Fig. 3. These controllers are set in cascade, where the output of the position controller, together with a feed-forward torque that comes from the rigid body inverse dynamics control, manipulates the set-point of the torque controller.

blockDiagramFigure 3: Block diagram of the cascade control employed on the HyQ's legs [2].



The key aspects for achieving high-performance torque control with a hydraulic system are:

  1. To use servovalves with high flow control bandwidth: HyQ uses high-spec valves (Fig. 2 - center), with bandwidth of about 250 Hz (for ± 25% opening), which are able to exploit the naturally high stiffness of hydraulics;
  2. To improve the controller using model-based control: HyQ employs model-based control approaches such as load velocity compensation and feedback linearization.


A simple model-based approach for improving torque tracking capabilities is the load velocity compensation [1]. In hydraulics, to compensate for the load velocity is equivalent to feed forward an extra flow such that the pressure in the cylinder chambers is kept constant while the rod is moving. Thus, the feedback force controller has to only supply an additional small flow to adjust the pressure difference between the chambers to reach the desired force. This load motion compensation permits to significantly improve the torque response. 

A more complex model-based control consists in linearizing the force dynamics by using the control approach feedback linearization [2]. This approach, besides compensating for the load motion influence, also linearizes the nonlinear pressure-flow characteristics.

Details about these model-based control approaches and results can be found in the following publications:

[1] T. Boaventura, M. Focchi, M. Frigerio, J. Buchli, C. Semini, G. A. Medrano-Cerda, D. G. Caldwell, "On the role of load motion compensation in high-performance force control", Proceedings IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), 2012, pp. 4066-4071, Vilamoura, Portugal.
[link]

[2] T. Boaventura, C. Semini, J. Buchli, M. Frigerio, M. Focchi, D. G. Caldwell, "Dynamic Torque Control of a Hydraulic Quadruped Robot", Proceedings IEEE International Conference on Robotics and Automation (ICRA), 2012, pp. 1889-1894, St. Paul, USA.
[link]


Main Results

The very satisfactory performance obtained with the torque-controlled leg of HyQ is shown in the following video, which presents results such as:

    • Friction and gravity compensation;
    • Great tracking at 5 Hz sinusoidal position reference;
    • Active compliance for safe human-robot interactions;
    • Drop tests.




 

Last Updated on Friday, 21 November 2014 10:01

INFORMATION NOTICE ON COOKIES

IIT's website uses the following types of cookies: browsing/session, analytics, functional and third party cookies. Users can choose whether or not to accept the use of cookies and access the website.
By clicking on further information, the full information notice on the types of cookies used will be displayed and you will be able to choose whether or not to accept cookies whilst browsing on the website.

Try our new site and tell us what you think
Take me there